Rodolfo Foschi Design - model Bernard · 2001

Original description

Ubicación: Leros (Dodecaneso), Grecia This Rodolfo Foschi 10 mt steel Cutter is available in Leros, Dodecanese, Greece. Bernard Model A single-chine steel cutter. The first example was built in 1995 for an offshore sailing enthusiast who commissioned naval architect Rodolfo Foschi to design a hull closely inspired by Tamata, the last yacht of the legendary Bernard Moitessier. Only five boats of this design were built. MATA HARI is a custum-made steel Cutter, builted by her first owner, an experienced welder, starting in 2001 and launched in 2008. The following documentation is available: • Declaration of conformity to the original design by Naval Architect Rodolfo Foschi. • Professional survey carried out by marine surveyor at the time of purchase in 2016 by actual owner (second owner). Principal Dimensions • Length Overall (LOA): 10.00 m • Beam: 3.30 m • Draft: 1.95 m • Maximum headroom: 1.95 m Accommodation • Forward double cabin • Two single berths aft • Convertible saloon double berth Heads • Jabsco marine toilet • Stainless steel sink • Shower Fresh Water System • Two pressure water systems: o Fresh water o Seawater • 15-litre Quick stainless steel water heater operating on both 220V shore power and engine heat exchanger. • Two stainless steel freshwater tanks, 200 litres each. Fuel • 300-litre fuel tank integrated into the keel. Ballast • 3,300 kg ballast in the keel. Interior Marine Okoumé plywood throughout. Galley • Stainless steel sink • Large worktop • Gimballed two-burner gas cooker • Gas oven Engine Perkins 4108M diesel engine, completely overhauled, coupled to a Borg-Warner gearbox. Shaft Drive • 30 mm stainless steel propeller shaft • Rubber cutless bearing • Volvo grease-lubricated shaft seal (replaced in 2023, serviced in 2025) Electronics • New Raymarine wind station (2025) • Nexus log and echo sounder • Raymarine wheel autopilot interfaced with Nexus system • Three instrument displays • 7" Lowrance chartplotter interfaced with the autopilot Rig Cutter rig. • 14 m Z-Spars deck-stepped mast • 4.80 m boom • Three reefing points led aft to the cockpit Winches • Two Antal self-tailing chromed winches • Two Antal traditional bronze winches Rope Clutches • Two banks of four Spinlock XTS clutches Standing Rigging • Upper and lower stainless steel shrouds, Ø10 mm • Forestay and inner forestay Ø10 mm • Textile gennaker halyard purchase Headsail Handling • Facnor twin-groove furling system • Bamar textile gennaker furler with 130 mm drum • Code 0 (110 m²), new in 2015 Sails • Fully battened mainsail with three reefing points, low-friction battcar system and lazy bag • Genoa (2012) in Dacron with UV protection • Staysail (2011) in Dacron with hanks Ground Tackle • Lofrans 1,200 W windlass • 60 m of 8 mm galvanized chain • Stainless steel chain locker • 16 kg Delta anchor Steering Wheel steering with stainless steel cables, emergency tiller, and external rudder fitted with 316 stainless steel pintles and gudgeons (Ø40 mm) running in nylon bushes. Hull Protection Awlgrip paint system including: • Epoxy zinc-rich primer • Five coats of anti-corrosion primer • Polyurethane topcoat with non-slip microspheres Electrical System • 90 W solar panel mounted on the stern arch, providing complete summer autonomy with the refrigerator running continuously. • LED interior lighting • LED navigation and anchor lights • High-intensity halogen searchlight with waterproof 12V socket • Stainless steel outboard lifting davit … Barco en venta a través de Yacht Studio (Roma / Leros). Más información: https://yachtstudio.it